EasyPSV Permanent Etch Adhesive (Sign) Craft Vinyl 12" x 12"

Description

Cutter Setting (EasyPSV Permanent Etch)
Cricut®
Silhouette Cameo
Scan N Cut
Roland GS/GX-24
Graphtec
Blade: Standard
Setting: Light Cardstock
Blade: Standard, 2
Setting: Vinyl
Material: Glossy
Speed: 7
Force: 11
Blade: Standard, 3
Cut Speed: 1
Cut Pressure: 2
Blade: 45°
Gram Force: 90-110
Offset: .250
Speed: 35 cm/s
Blade: 45°
Gram Force: 9
Tool: CB09U+0
Speed: 35 cm/s
Application Instructions
- Place EasyPSV with the liner side down and cut your design (DO NOT reverse/ mirror your design)
- Weed excess vinyl
- Remove the application tape's paper liner and place tape on top of EasyPSV
- Burnish with a squeegee
- Lift the application tape and EasyPSV away from the paper liner.
- Place the application tape on your desired object
- Burnish with a squeegee to fully adhere the design
- Gently peel away the application tape, leaving just your EasyPSV design on the object
Recommended Accessories & Care
EasyPSV Etch Applies to
Recommended Accessories
Care Instructions
Glass/mirrors
Wood
Plastic
Metal
Ceramic
Siser Weeder
Siser Application Tape
Siser Squeegee
Not recommended for use near flame/ heat
source, or with microwave, or dishwasher.
Not recommended for use on drywall or other painted surfaces
* Multiple quantities of the same color will be sent as a continuous roll unless requested otherwise.
Outdoor Durability
Up to 7 years depending on climate and UV exposure.
Thickness
3.0 mil (76.2 micron)
Adhesive
Permanent, Solvent based
Liner
78# Kraft
Minimum, Application Temperature
+40° F
Shelf Life
1 year when stored at 70° F and 50% relative humidity.
Surface Prep Instructions
For best adhesion, remove any dirt, dust, grease, etc to prepare the surface you want to
decorate with EasyPSV. The following cleaning method is not recommended for porous surfaces
such as unfinished/untreated wood. It is recommended that all other surfaces be spot tested
with care before cleaning the entire application area.
Non-porous surfaces can be cleaned with a mix of approximately 2 parts water and 1 part isopropyl
alcohol (70% or higher for best results) or non-ammonia based window cleaner. Use a microfiber or
lint free towel to clean the application area with the mixture.Paper towel is not recommended
since it will leave behind small bits of paper that can become trapped under the EasyPSV during
application. Ensure the area is completely dry before applying.
*The cleaning method outlined above is subject to modification and not always suitable for every substrate.
The purchaser should independently determine with their own testing to use this method or not on a case by case basis.
Application Instructions
1. Place EasyPSV with the liner side down and cut your design. (DO NOT reverse/mirror your design.)
2. Weed excess vinyl.
3. Remove the application tape's paper liner. Place tape on top of EasyPSV and burnish with a squeegee.
4. Lift the application tape and EasyPSV away from the paper liner to expose the permanent adhesive.
5. Place the application tape on your desired object and burnish with a squeegee to fully adhere the design.
6. Gently peel away the application tape, leaving just your EasyPSV design on the object.
Removal Instructions
If the EasyPSV peels up, but leaves an adhesive residue use an adhesive remover to clean the area.
If the EasyPSV is stubbornly sticking, the heat from a hair dryer or garment steamer can help loosen the
adhesive. However, heating is not recommended for glass due to possible shattering. To remove Permanent
EasyPSV from glass, saturate the decal with soap and water. Cover with plastic wrap and let sit for a few
hours before attempting to remove. An adhesive remover may still be required to clean all adhesive from
the surface after removing the EasyPSV.
*The removal instructions outlined above are subject to modification and not always suitable for every substrate.
The purchaser should independently determine with their own testing to use this method or not on a case by case basis.
Storage Instructions
For best results, avoid direct sunlight and extreme temperatures. Ideally, temperatures should not surpass
70° F and 50% relative humidity. When stored properly, EasyPSV Etch has a shelf life of up to 1 year.
Payment
Shipping
Same Day or 1 day Shipping for orders placed
before 3:00 PM (Monday-Friday)
2-4 business day transit time.
See map above
Payment and Return/Exchange
Change pick up hours to Monday-Friday 8:00-4:00.
Same day pick up as long as order is placed
before 3:00 PM.
Please bring valid ID and invoice.